Setting up A Bathtub
View WebsiteThe publisher is making a few great pointers on How to Install a Bathtub Yourself as a whole in this great article which follows.
Installing a bathtub isn't specifically brain surgery, however it does need solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately difficult project. If the old tub is readily obtainable, the job can move quickly; if you have to open up a wall surface to eliminate the old tub and position the brand-new bath tub, the job is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. Make sure you have certified on your own for the task as well as are comfortable attempting it. Rather than hiring a service provider to take control of a halfway-completed project, it is better to take into consideration utilizing one before you start. Opportunities are you may require an expert plumber to make tube connections.
This write-up will certainly help you install a brand-new tub in your bathroom if you have actually already bought a brand-new tub and also do not need to transform the plan of your previous supply of water pipelines.
Your tools and material checklist must make up the following:
Getting ready for the Installation
First of all, the sustaining framework provided with the bathroom should be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you should do is separate the supply of water. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be rather bothersome due to the limited accessibility that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipes. Once the supply pipelines have actually been removed, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Using the two wooden boards under its feet, put the tub in the called for placement. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the spirit level reads level.
To install faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Activate the water and also examine all joints as well as brand-new pipework for leaks as well as tighten them if required. Fill the bathtub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, deal with the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has actually been utilized at least when as this will certainly resolve it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and also the sink. Safeguard the tap in position with the maker given backnut. When the tap is firmly in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind should be attached to the tap finishes initially, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to crack a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about problems with wetness and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to always load the bathtub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealer can fracture fairly early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily available on the market. It is suggested to fit the tiles using water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog entry about How to Install a Bathtub Yourself while surfing the web. Sharing is nice. You just don't know, you might be doing someone a favor. I appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book Your Service